10 Tell-Tale Signs You Need To Look For A New Car Ignition Lock > 자유게시판

Why is My Car Ignition Locked?

There are many reasons why your ignition might be stuck. The key may be dirty or may have a damaged wafer inside it. You can fix car ignition this by sliding the key into and out of the cylinder a few times.

The pins of the lock cylinder may also be stuck. You can employ a small tackhammer to lightly tap on the cylinder to loosen them.

Check the Battery

If your car is in Park or neutral, but won't turn on when the key is inserted into the ignition, it may be a problem with the shifter switch on the transmission. This can be easily fixed by moving the shifter up or down to put the car into gear.

If it's still not turning, the problem could be related to the neutral safety switch or the transmission shifter cable. A mechanic or local auto locksmith can easily solve these issues.

It's also possible that the ignition cylinder has worn out. In time, both the ignition and key may wear out making them difficult to insert or remove. A lubricant, such as silicon lock grease could solve this problem, allowing the wafers to slide into the proper position.

The filth from your pockets and adhesive from tape that holds packages together can build over the key, preventing it from being able to slide into the ignition. Clean the key using a cloth, or a cleaner like Triflow, to solve this issue. You may also try a spare key in order to determine if the issue is with the ignition or the key.

You can also tap the key with a small hammer, when it's in the ignition. This will create a slight vibration that may be enough to loosen the wafers in the ignition, allowing them to slide in place. But, be careful not to harm the key or the ignition cylinder.

If all of the above methods are unsuccessful, it's time to contact a locksmith or automotive mechanic to have it examined. It could be that the key has been damaged inside the ignition or it may be time to replace the whole thing. A locksmith can make an alternative key if the problem is with the key. If the ignition cylinder is the cause then you'll need to bring the vehicle to a repair shop in order for it to be repaired. Luckily, these problems are usually very easy to fix.

Check the steering wheel

A steering wheel that is locked can cause the ignition to stop turning. This happens if the driver is unable to engage it when they exit or enter the vehicle. It is usually caused by yanking on the wheel and securing themself against it with their hands. It could also happen when an individual in the rear seat has a mishap and engages the brakes while they exit the vehicle.

This is a simple fix that doesn't involve going to the mechanic or locksmith. First, make sure the shifter is either in Park or Neutral. If it's not you can gently pull or push the gear shifter until it shifts to one of these positions. You must also turn on the handbrake or press the brake before turning the key.

If the wheel is not locked, a quick inspection of the steering column should determine if the key is engaged with the lock cylinder. A small "Lock' label is usually found in the lower portion the ignition circle. It is possible to disengage this by gently jiggling or pulling the key with moderate force. It is essential not to apply too much pressure since it could damage the key or damage a wafer inside the lock cylinder.

A spare key can also be used to disengage the lock. This could indicate that the key is worn out and no longer able engage the wafers within the lock cylinder. If this is the situation then a professional at Karl Chevrolet Webster City will be able to design a replacement key.

If the new key still does not engage, a short spray of penetrating oil can assist. Apply a small amount of penetrating oil around the ignition and keyhole. Then, jiggle the key or tap it lightly to make sure it is working. If this does not work, you may need to consult a specialist in your local dealership for cars. They'll be able give you a new key and also replace the ignition cylinder in the event that it is required.

Check the Key

If you are unable get your key to turn in the ignition, it is likely that there is something wrong with your key. Try taking off any foreign material on the key (lint and adhesive from packing tape, etc). You may also try alcohol on the key or Goo Gone to see if it helps.

If the pins inside the lock do not move in a proper manner when you insert your key, it's possible that they are stuck. You can test the spare key by gently removing it of the ignition after you put it in. You should be in a position to feel and hear the pins move inside. If not, you can grease the pins using graphite powder. You can buy graphite in small tubes that can be applied directly to the keyhole. This will allow the pins to slide into position when you insert the key and stop them from getting stuck.

A more serious issue with your key could be that it is damaged or worn and is unable to connect the internal pins in the ignition cylinder. This can cause the cylinder to stop to turn, preventing you from starting your vehicle. If this happens you'll need to take your car to repair or locksmith shop for repair.

If you're able to turn your car on with an extra key, and you've ruled out any issues with the steering wheel or battery it could be that the ignition and key replacement cylinder has worn out. You can attempt to loosen the lock cylinder using the blunt end of a screwdriver or the handle of a Hammer (not the head). Gently tapping on the cylinder will often free it, allowing you to turn your key and start your car. If this doesn't work, you will need to replace the lock cylinder by an expert mechanic.

Check the Ignition Socket

The ignition socket is the place your key slides in and out of place when you insert it. It could get blocked with debris, or just wear and tear. Try putting some silicon lock lubricant (like WD-40) into the ignition to make things move along.

You can also use the small hammer and tap gently on the inside of the ignition to loosen or reset the pins that are out of alignment. Be cautious not to overdo it, or you could cause severe damage to the ignition switch.

It is important to check whether your car's transmission is set to neutral or park before you attempt this. A lot of newer cars come with a system that can lock the steering wheel when it is not in park or neutral that can stop the key from being turned in the ignition.

If you've done all of this and still not able to get your key to rotate it is likely that the ignition cylinder housing needs replacement. Different vehicles have different methods of replacing the ignition cylinder, therefore it is important to follow the correct steps.

This usually involves removing the plastic covering that covers the steering column and the ignition assembly. To remove this cover, you will need to first adjust the tilt-wheel to the lowest setting and then unscrew any fasteners that hold it in place.

After you have removed the cover, you'll need to remove the old ignition cylinder from the steering column. Then, you will need to compare the new ignition cylinder that you purchased with the one that was removed to make sure that they're identical. After this is completed, you can install the new ignition cylinder in the same way that you did with the old one.

Sometimes, despite all of our best efforts, the ignition will become damaged and require replacement. If this happens, it's advised to contact a Tempe Locksmith for assistance. A locksmith can help you determine the correct replacement and install it correctly so that your car ignition switch replacement can restart.