Are You Sick Of Fiat Panda Key Fob Replacement? 10 Inspirational Resources To Revive Your Passion > 자유게시판

Reasons Your fiat 500 spare key cost 500 Key Fob Won't Work

A fiat abarth key fob for the Fiat punto remote key 500 allows you to easily open doors and start your car. There are a myriad of reasons why the fob won't be working. This could be due to a dead coin-battery or water damage, problems with the receiver modules, and interference.

This listing is for a NEW replacement fiat grande punto key Flip Key Remote that is similar to the Ilco brand. It must be professionally programmed (click here to find local locksmiths in the automotive industry). Includes lock, unlock, and trunk buttons.

Dead Coin Battery

A dead battery is probably the most common cause of your 500 key fob not working. Modern key fobs offer only a limited range of operation and must be within a few inches of the vehicle to function. If you're far away from your vehicle when you press the key fob button, the car won't respond, and will display a "Key Fob Not Detected" message in the instrument cluster.

If this happens, simply replace the battery in the coin cell (Part number CR2032) by a new one from a reputable manufacturer like Panasonic, Duracell, or Energizer. They can be found in the local hardware store or online.

You can test the battery of your coin-cell by pressing the buttons while standing near your lost fiat 500 car key 500. The car will blink its parking lights, and the key fob should operate the lock and unlock switches.

If the fob's key doesn't function after replacing the battery, it may have water damage that prevents it from communicating with the receiver module in your vehicle. Water damage can occur in many ways, including simply splashing or submerging the key fob saltwater at the beach. If you suspect that your fob has been exposed to water, you can place it in a bag of rice to draw out the moisture. If that doesn't work, the fob might require reprogramming by an experienced auto locksmith or by the dealer.

Water Damage

Damage to the water supply can occur if you immerse the fob into the ocean or wash it in a machine. Saltwater is particularly dangerous to the fob's circuit board that can cause it to short out and eventually die. It's not good to soak the fob in water however, but don't give it up when you accidentally drop it in water or fail to take it out of your pants pocket.

First take the battery off the fob. Clean the electronic chip with isopropyl alcohol or a similar product and dry it thoroughly before replacing the battery. Then check the fob to test if it works. If the key isn't working, it may have to be reprogrammed. This is usually handled by a professional or dealer auto locksmith.

If your key is older and is not programmed for your vehicle, you will need to replace it completely. A professional locksmith for automotive can carry out this simple task. The locksmith will have to cut the key to match the ignition of your car. The locksmith also needs to reprogram the fob into the vehicle's system. This is a cheap and fast process that can be completed the same day.

Receiver Module Issues

The 500 key fob you have may be inoperable because it's out of range. The remote typically has a range of 30 feet or less and if it's far away from your car it won't respond to your commands. It's easy to solve this issue by moving the remote closer to your car until it responds.

If your fob won't work after you replace the coin battery, also called a "button", "watch" or "button", it could be due to a problem with the circuit board inside. Reprogramming the fob usually resolves this problem. You can find directions on how to do this for the majority of automobiles by searching YouTube or consulting the owner's manual.

It may be necessary to replace the clips made of metal that hold the coin batteries in the correct position. If they loose tension, it could hinder the battery from sitting properly and can cause the remote to malfunction.

In rare cases the fob may be out of the vehicle's sync because due to hardware or software issues. It is possible to fix this issue by visiting your local dealer or auto-locksmith to reprogram your key fob. In certain situations they might need to reinstall the software in your body control module, too.

Interference

In addition to a dead coin battery the key fob could not be receiving or transmitting an signal due to interference. This is possible when the key fob is in proximity to an electronic radio transmitter (cell phones or radar detectors) or any other source of electromagnetic radiation. Other reasons the key fob may not function include a weak connection to the buttons and internal chip, or water damage.

If your key fob suddenly stopped working, or if you've tried everything at home to resolve it (e.g. It could be a defective 500 receiver module if you've tried replacing the battery, reprogramming, and using an alternative key fob. The receiver module, which is located under the dashboard, is able to pick up radio frequency signals from your key fob. Then, it converts them into electronic commands that the vehicle interprets.

Luckily, there is an easy way to reset all of the on-board systems in your 500 device, including the key fob. Disconnect the 12 volt battery for approximately 15 minutes by removing the negative cable and then the positive cable. Then reconnect the battery. This will remove any remaining electric current, and also restart the computer in your car. This could help you get your key fob to work again. If the issue continues, you should seek out an expert technician. They will be able to determine the exact cause of any problems.